RIDGID 1822-I Operator's Manual Page 19
- Page / 71
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Ridge Tool Company • Elyria, Ohio • U.S.A.
17
Figures 21B – Remove Jaw Insert
4. On a work bench, drive out top pins holding center-
ing finger in place and install new centering finger.
NOTE! When driving pin out on work bench, do not
bend centering finger.
5. Reinstall jaw insert and finger, and tighten screw.
Rear Centering Finger/Jaw Replacement
1. With rear centering jaw in the OPEN position
unplug machine and remove rear cover.
2. Remove three e-clips holding rear retainer in place
and remove retainer. (Refer to Figure 24 Step 1.)
3. Remove spacers and rear centering jaws.
4. On a work bench, drive out pins holding centering
finger in place and install new centering finger.
5. Reinstall rear jaws and spacers on rods. (Refer to
Figure 22.) Locate square pin in jaw slot.
Figure 22
6. Reinstall rear retainer and retaining clips.
NOTE! Before reinstalling machine covers refer to
Figure 22 and check for proper jaw orientation.
Spindle Conversion Kit for
Plastic Coated Pipe
Figure 23 – PCP Kit
Spindle Assembly Removal
1. With machine OFF and unplugged, remove front
and top covers.
2. Remove rear centering assembly.
3. Remove three (3) brake shoes. (Refer to Figure 24.)
4. Remove small E-clips and washers holding front
jaws to drive sprocket. Slide out spindle assembly.
Spindle Assembly Installation
1. Following reverse procedure, install new spindle
assembly for plastic coated pipe.
2. Install the E-clips and washers on the front jaws.
3. Reassemble the three (3) brake shoes.
NOTE! Tighten shoulder bolts until they bottom out.
4. Reassemble rear centering assembly using new
spacers and rear jaws supplied with the kit.
NOTE! Rear jaws must be oriented as shown for right
hand threading. (Refer to Figure 25.)
5. Install top and front covers.
NOTE! Once the machine is fitted with the new kit to
thread plastic coated pipe, it is also capable of
threading steel and galvanized pipe sizes
1
/
2
″ – 2″. If
sizes smaller than
1
/
2
″ pipe as required, the original
front and rear jaw assemblies must be installed.
1822-I Pipe and Bolt Threading Machine
- Pipe and Bolt 1
- Threading Machine 1
- Table of Contents 2
- Pipe and Bolt Threading 3
- General Safety Information 4
- Specific Safety Information 5
- ▲ WARNING 6
- Standard Equipment: 7
- Accessories 7
- Die Heads and Dies 7
- Machine Dimensions and 8
- Bench/Stand Mounting 8
- Performance Tips 8
- Folding Wheel Stand 9
- Know Your Machine 10
- Machine Operation Using 11
- Standard Equipment 11
- Self-Opening Die Head 12
- Cut-Off and Reaming Tips 12
- Speed Selection 12
- Model 1822-I 12
- Threading Pipe with No. 815A 12
- Automatic Pipe Release 13
- Changing Dies 13
- No. 819 Nipple Chuck and 14
- No. 839 Adapter Kit 14
- Adjusting No. 141 Geared 14
- Threader 14
- Operating No. 141 Geared 15
- Mount Kit 15
- No. 821 Blade Cutter and 16
- No. 822 Adapter Kit 16
- No. 1460 Oil Pan Cover Kit 17
- Installation 17
- Maintenance 18
- Spindle Conversion Kit for 19
- Plastic Coated Pipe 19
- Service & Repair 20
- Left Hand Machine Operation 20
- Operation 21
- Left Hand Operation 21
- 1822-IC 22
- Machine à fileter les tuyaux 23
- Table des matières 24
- Consignes de sécurité 25
- Réparations 26
- ▲ MISE EN GARDE 27
- Description 28
- Spécifications 28
- Equipements de base : 29
- Accessoires 29
- Dimensions de la machine et 30
- Conseils d’utilisation 30
- Figure 7 – Coupe-tubes N 33
- Remplacement des filières 35
- Mandrin à raccords N 36
- Réglage de la fileteuse 37
- Utilisation de la fileteuse 38
- 141 avec le kit 38
- Utilsation 40
- Entretien 41
- Dépose de l’arbre 42
- Entretien et Réparations 43
- Schémas électriques 46
- 1822-I Máquina Roscadora 47
- NO SE RECOMIENDA 49
- Seguridad personal 50
- Servicio 50
- ▲ ADVERTENCIA 51
- Descripción, Especificaciones 52
- Equipo estándar: 53
- Accesorios 53
- Dimensiones de la máquina y 54
- Recomendaciones para 54
- No. 1404 55
- Funcionamiento de la máquina 56
- Figura 7 – Cortadora No. 364 57
- Selección de velocidades 58
- Modelo No. 1822-I 58
- Cambio de terrajas 59
- Portaherramientas Niplero No 60
- 819 y Juego Adaptador No. 839 60
- Regulación de la Roscadora de 61
- Engranajes No. 141 61
- Funcionamiento de la 62
- Roscadora a Engranajes No 62
- 141 con el Juego No. 241 para 62
- Montaje en el Carro 62
- Cortadora de Cuchilla No. 821 63
- Instalación 64
- Mantenimiento 65
- Juego transformador del 67
- Servicio y reparaciones 68
- Ventilador 70
- LIFETIME WARRANTY 71
- GARANTIE A VIE 71
- GARANTIA DE POR VIDA 71
Related products and manuals for Sewing machines RIDGID 1822-I
(79 pages)
Sewing machines Ridgid 1210 User Manual
(2 pages)
(2 pages)
Sewing machines Ridgid 300 User Manual
(1 pages)
(1 pages)
Sewing machines Ridgid 1233 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 0.182 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals