RIDGID JP0600 Specifications download pdf (Page 26)

Safety Instructions for Basic Jointer/Planer Operation

Before Each Use

Inspect your jointer/planer.

WARNING: The 2-1/2 inch jointer/planer pulley and

the 3-1/2 inch motor pulley furnished will run the

cutter head at about 5000 RPM when used with a

3450 RPM motor. Use of different types of pulleys

or motors will change this speed and could cause

jamming, binding, kickback, thrown blades or

other dangers.

• To reduce the risk of injury from accidental starting,

always turn switch off, remove switch key and unplug

jointer/planer before installing or removing any blade,

accessory or attachment or making any adjustments.

• If any part is missing, bent or broken in any way, or any

electrical part does not work properly, turn the jointer/

planer off and unplug the jointer/planer.

• Replace damaged or missing parts before using the

jointer/planer again.

• Make sure the cutter head turns in the right direction.

The top should move toward the infeed table. Call an

Authorized Service Center for help if the cutter head

turns the wrong way.

• Keep Jointer/Planer interior, free of wood chips and

dust buildup around motor and switch box.

• Keep blades sharp. Dull or nicked blades tend to

“pound” and chew at the wood, causing kickbacks.

• Make sure the cutter guard works properly. With the

switch off and key removed, pull the cutter guard open

and let go. If the guard doesn’t smoothly swing closed,

contact an Authorized Service Center.

• Don’t force the tool. It will do the job better and safer at

the rate for which is was designed.

Push blocks and push sticks

Two plastic push blocks are supplied with your jointer/

planer. Use them when practical. The rubber sole of the

push blocks give better traction with the wood than your

hands do. If they become slippery, they can be cleaned

with rubbing alcohol, paint thinner or sandpaper.

CAUTION: Use rubbing alcohol or paint thinner

only as described on their containers. Use only in

well ventilated areas away from open flames,

sparks or heat sources.

Push blocks can’t always be used. With larger work-

pieces, you may have better control of the workpiece

using your hands. Always make a test pass first to deter-

mine which method gives you better control.

Before you make any cut, plan your hand positions. If a

kickback should occur, plan so that your hands will not fall

or be forced into the cutters.

Three Inch Rule (3")

Generally, if your hands are closer than three inches to

the blade as you feed the wood, use push blocks. This

gives extra protection to your hands by placing the push

blocks between your hands and the cutters.

Always Use Push Blocks When Planing, Beveling Or

Chamfering

When jointing, test for workpiece stability before actually

jointing, and use push blocks when you can without sacri-

ficing control.

Feeding the Workpiece (All Operations)

CAUTION: Test for workpiece stability with and

without the push blocks before turning the jointer/

planer on. See earlier section “Push Blocks and

Push Sticks”.

• Support long workpieces at both infeed and outfeed,

as shown on page 30.

• Feed with grain whenever possible. When necessary

to feed against grain, take very light cuts and feed

slowly to minimize workpiece splintering, breakage or

dangerous kickback.

• Keep steady pressure down on table and back against

fence.

• As leading edge of board passes by cutterhead,

slightly shift pressure to above cutterhead and outfeed

table, away from infeed table. Keep pressure at outfeed

table and near cutterhead for remainder of cut.

• Use hand-over-hand motion, releasing forward hand

and moving it to rear, to continue feeding workpiece.

• Feed the board at a continuous rate until the cut is

made along the entire length of the board. Any hesita-

tion or stopping could cause a “step” on the edge of

the board, resulting in an uneven edge as the cut is

completed.

• If it is difficult to maintain steady rate, table or fence

may need waxing (see Maintenance Section of man-

ual.)

•

To Reduce the Risk of Injury From Jams, Slips Or Thrown Pieces (Kickbacks Or Throwbacks)

• Use this jointer/planer to cut only wood.

• Plan your hand placement so your fingers will not be

anywhere a sudden slip could cause them to slide or

fall into the cutter head. When using only one hold-

down/push-block to feed the wood, do not put your

other hand on the jointer/planer, workpiece, or hold-

down/push-block.

• Make sure the clamps and locks are tight and there is

not excessive play in any parts.

• To reduce the risk of injury from thrown pieces, make

sure the blades are properly installed and the cutter

blade wedge screws are tight.

• Adjust the depth of cut to between 1/32 and 1/16 of an inch

for best results in most operations. A deep cut makes feed-

ing the wood harder and can cause the wood to kickback.

To be sure you will make a depth of cut you planned,

always lower the infeed table slightly farther than you

wanted. Then, raise the table to the desired depth.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 43 44

Comments to this Manuals

No comments

RIDGID JP0600 Specifications Page 26

Comments to this Manuals

Related products and manuals for Unknown RIDGID JP0600