RIDGID 1822-I Operator's Manual Page 17
- Page / 57
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
916 Roll Groover
Ridge Tool Company 15
Incorrect size of Grooving and Driving Rolls.
Mismatched Grooving and Driving Rolls.
Grooving Roll and/or Driving Roll worn.
Pipe length not straight.
Pipe end not square with pipe axis.
Pipe not level.
Pipe axis not offset
1
/
2
degree from Driving Roll axis.
Groover not level.
Pipe not level.
Pipe length not straight.
Pipe end not square with pipe axis.
Pipe stands too close to end of pipe.
Pipe end flattened or damaged.
Hard spots in pipe material or weld seams harder
than pipe.
Grooving Roll hand feed rate too slow.
Power Drive speed exceeds 36 RPM.
Pipe supports Stand Rollers not in correct loca-
tion for pipe size.
Maximum pipe wall thickness exceeded.
Wrong rolls.
Pipe material too hard.
Adjustment screw not set.
Power Drive does not supply required minimum
torque.
Maximum pipe diameter tolerance exceeded.
Mismatched Grooving and Driving Rolls.
Depth adjustment screw not set correctly.
Grooving Roll hand feed rate too slow.
Driving Roll knurling plugged with metal or worn flat.
Power Drive does not supply minimum required
torque.
Chuck not closed on drive shaft flats.
Pipe Support Stand too close to Groover.
Install correct size of Grooving and Driving Rolls.
Match Grooving and Driving Rolls.
Replace worn Roll.
Use straight pipe.
Cut pipe end square.
Adjust stand to level pipe.
Offset pipe
1
/
2
degree.
Level Groover.
Adjust stand to level pipe.
Use straight pipe.
Cut pipe end square.
Move pipe stand in
1
/
4
distance from end of pipe.
Cut off damaged pipe end.
Hand feed Grooving Roll into pipe faster.
Hand feed Grooving Roll into pipe faster.
Reduce speed to 36 RPM.
Position Pipe Stand Rollers for pipe size being
used.
Check pipe capacity chart.
Install correct rolls.
Replace pipe.
Set depth.
Use RIDGID No. 300, 36-RPM Power Drive.
Use correct diameter pipe.
Match Grooving and Driving Rolls.
Adjust depth setting.
Hand feed Grooving Roll into pipe faster.
Clean or replace Driving Roll.
Use RIDGID No. 300, 36 RPM Power Drive, 535
or 1822-I Machine.
Close chuck.
Move pipe stand
1
/
4
distance in from outer end of
pipe.
PROBLEM CAUSE CORRECTION
Roll Groove too narrow
or too wide.
Rolled Groove not per-
pendicular to pipe axis.
Pipe will not track while
grooving.
Pipe flared at grooved end.
Pipe drifts back and forth
on Driving Roll axis while
grooving.
Pipe rocks from side to
side on Driving Roll
while grooving.
Groover will not roll
groove in pipe.
Groover will not roll
groove to required
diameter.
Pipe slips on Driving Roll.
Groover will not rotate
pipe while grooving.
Pipe raises or tends to tip
Groover over backwards.
Table III. Troubleshooting
- Portable Roll 1
- Table of Contents 2
- General Safety Information 4
- Specific Safety Information 5
- Roll Groover Assembly 6
- Instructions 6
- Description, Specifications 6
- Standard Equipment and 6
- (Figure 2) 7
- Machine Inspection 8
- Machine and Work Area Set-Up 9
- Pipe Preparation 10
- Pipe/Tubing Length 10
- Pipe Set-Up 10
- Adjusting Roll Groove Depth 11
- Forming the Roll Groove 12
- Pipe Diameter Reference 12
- Removing and Installing 13
- Roll Grooving Smaller 14
- Diameter Steel Pipe 14
- Accessories 14
- Roll Grooving Copper with 14
- Maintenance Instructions 15
- Service and Repair 15
- 916 Roll Groover 16
- Ridge Tool Company14 16
- Table III. Troubleshooting 17
- Ridge Tool Company16 18
- Rainureuse à galets n° 916 19
- Table des matières 20
- Déconseillé 21
- Consignes de sécurité 22
- Description, spécifications 23
- Assemblage de la rainureuse 24
- (Figure 4) 25
- Inspection de la machine 26
- MISE EN GARDE 27
- AVERTISSEMENT 27
- Préparation des tuyaux 28
- Longueur des tuyaux 28
- Installation des tuyaux 28
- (Figure 9) 29
- (Figure 10) 29
- Tableau B (Figure 11) 29
- Exécution des rainures 30
- Dépose et installation 31
- Exécution du rainurage 32
- Rainurage des tuyaux d’acier 33
- Accessoires 33
- Entretien 33
- Service après-vente 33
- Ridge Tool Company32 34
- Tableau III. Dépannage 35
- PROBLEME CAUSE REMEDE 36
- Tableau de dépannage 36
- Ranuradora a rodillos 37
- NO SE RECOMIENDA 39
- Información específica 40
- Descripción 41
- Especificaciones 41
- No. en el Modelo Peso 42
- (Figura 4) 43
- Revisión de la máquina 44
- ADVERTENCIA 45
- Funcionamiento de la 46
- Ranuradora a Rodillos No. 916 46
- Regulación de la profundidad 47
- (Figura 10) 48
- (Figura 11) 48
- Ranurado de tubos cortos 49
- Extracción e instalación 50
- Ranurado en cobre con la 51
- Ranurado de tubos de acero de 51
- Accesorios 51
- Instrucciones para 52
- Mantenimiento y reparaciones 52
- Ridge Tool Company 51 53
- PROBLEMA CAUSA CORRECCION 54
- PROBLEMA CAUSA CORRECTION 55
- Tabla de detección de averías 55
- Ridge Tool Company54 56
- Ridge Tool Company 57
- 400 Clark Street 57
- Elyria, Ohio 44035-6001 57
Related products and manuals for Sewing machines RIDGID 1822-I
(55 pages)
Sewing machines Ridgid 1210 User Manual
(2 pages)
(2 pages)
Sewing machines Ridgid 300 User Manual
(1 pages)
(1 pages)
Sewing machines Ridgid 1233 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 0.390 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals