RIDGID 1822-I Operator's Manual Page 14
- Page / 57
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
916 Roll Groover
Ridge Tool Company12
Removing or Installing Drive Roll
1. Remove 4 bolts that hold rear bearing retaining plate
and remove plate.
(Figure 17)
Figure 17 – Remove Retaining Plate
2. With mallet, lightly tap on front of drive shaft to release
shaft and rear bearing from unit.
3. Pull drive shaft and bearing from unit, and replace with
proper shaft.
NOTE! Replacement drive shaft come equipped with
rear bearing.
Roll Grooving Copper with
No. 916
Tubing Preparation
1. Copper tubing ends must be cut square.
2. Tubing out-of-roundness must not exceed the total
O.D. tolerance listed in groove specifications.
NOTE! Determine out-of-roundness by measuring max-
imum and minimum O.D. at 90 degrees apart.
Make sure that copper drive and groove rolls are
installed before attempting to roll groove copper.
Forming Roll Groove
1. Set adjustment screw for depth required.
(See Chart
C below.)
Depth Adjustment Chart for Copper Roll Set
NOTE! Additional adjustment may be necessary to
achieve proper groove diameter. Chart above is
for reference only
2.Square copper tubing and pipe stand to roll groover,
making sure the workpiece is flush against drive roll
flange.
3. Level copper tubing by adjusting pipe stand. Copper
tubing and machine should both be leveled.
4. Follow instruction in section “Forming the Roll Groove”
on
page 10.
Roll Grooving Smaller
Diameter Steel Pipe
1. Adjust feed screw for depth required.
(See Chart D
below.)
NOTE! Additional adjustment may be necessary to
achieve proper depth. Chart above is for refer-
ence only.
2. Follow instructions in section “Forming the Roll
Groove” on
page 10.
NOTE! 1
1
/
4
″ and 1
1
/
2
″ in
Chart D
refers to the use of
optional AWWA roll set. See Chart B for adjust-
ment when using
standard
roll set.
Accessories
Only the following RIDGID products have
been designed to function with the 916 Roll Groover.
Other accessories suitable for use with other tools may
become hazardous when used on this Roll Groover.
To prevent serious injury, use only the accessories listed
below.
NOTE: A Roll Set Consists of a Groove Roll and a Drive Roll.
NOTE! See Ridge Tool catalog for listing of pipe stands.
Schedule 10 Schedule 40
Diameter Minimum No. of Turns Minimum No. of Turns
1″ 54
1
/
4
1
1
/
4
″ 3
1
/
2
3
1
1
/
2
″ 3
3
/
4
3
1
/
2
Chart D
Number of Turns
Diameter K L M DWV
2″ 44
1
/
4
4
1
/
2
—
2
1
/
2
″ 3
1
/
2
44
1
/
4
—
3″ 3
1
/
4
3
1
/
2
4
1
/
4
4
3
/
4
4″ 2
1
/
2
3
1
/
4
3
1
/
2
4
1
/
2
5″ 1
3
/
4
2
3
/
4
3
1
/
4
4
1
/
4
6″ 1
1
/
4
2
1
/
2
34
1
/
4
Chart C – Depth Adjustment Chart for Copper Pipe
WARNING
Catalog Model
No. No. 916 Accessories
45347 — Roll Set for 1″ Schedule 10, 40 (Optional)
45352 — Roll Set for Copper (Optional)
69667 — Roll Set for 1
1
/
4
″ - 1
1
/
2
″ AWWA (Optional)
69692 — Roll Set for 2″ - 6″ AWWA (Optional)
67662 — Adapter Bracket for 300 Compact
76822 — English Diameter Tape
76827 — Metric Diameter Tape
- Portable Roll 1
- Table of Contents 2
- General Safety Information 4
- Specific Safety Information 5
- Roll Groover Assembly 6
- Instructions 6
- Description, Specifications 6
- Standard Equipment and 6
- (Figure 2) 7
- Machine Inspection 8
- Machine and Work Area Set-Up 9
- Pipe Preparation 10
- Pipe/Tubing Length 10
- Pipe Set-Up 10
- Adjusting Roll Groove Depth 11
- Forming the Roll Groove 12
- Pipe Diameter Reference 12
- Removing and Installing 13
- Roll Grooving Smaller 14
- Diameter Steel Pipe 14
- Accessories 14
- Roll Grooving Copper with 14
- Maintenance Instructions 15
- Service and Repair 15
- 916 Roll Groover 16
- Ridge Tool Company14 16
- Table III. Troubleshooting 17
- Ridge Tool Company16 18
- Rainureuse à galets n° 916 19
- Table des matières 20
- Déconseillé 21
- Consignes de sécurité 22
- Description, spécifications 23
- Assemblage de la rainureuse 24
- (Figure 4) 25
- Inspection de la machine 26
- MISE EN GARDE 27
- AVERTISSEMENT 27
- Préparation des tuyaux 28
- Longueur des tuyaux 28
- Installation des tuyaux 28
- (Figure 9) 29
- (Figure 10) 29
- Tableau B (Figure 11) 29
- Exécution des rainures 30
- Dépose et installation 31
- Exécution du rainurage 32
- Rainurage des tuyaux d’acier 33
- Accessoires 33
- Entretien 33
- Service après-vente 33
- Ridge Tool Company32 34
- Tableau III. Dépannage 35
- PROBLEME CAUSE REMEDE 36
- Tableau de dépannage 36
- Ranuradora a rodillos 37
- NO SE RECOMIENDA 39
- Información específica 40
- Descripción 41
- Especificaciones 41
- No. en el Modelo Peso 42
- (Figura 4) 43
- Revisión de la máquina 44
- ADVERTENCIA 45
- Funcionamiento de la 46
- Ranuradora a Rodillos No. 916 46
- Regulación de la profundidad 47
- (Figura 10) 48
- (Figura 11) 48
- Ranurado de tubos cortos 49
- Extracción e instalación 50
- Ranurado en cobre con la 51
- Ranurado de tubos de acero de 51
- Accesorios 51
- Instrucciones para 52
- Mantenimiento y reparaciones 52
- Ridge Tool Company 51 53
- PROBLEMA CAUSA CORRECCION 54
- PROBLEMA CAUSA CORRECTION 55
- Tabla de detección de averías 55
- Ridge Tool Company54 56
- Ridge Tool Company 57
- 400 Clark Street 57
- Elyria, Ohio 44035-6001 57
Related products and manuals for Sewing machines RIDGID 1822-I
(55 pages)
Sewing machines Ridgid 1210 User Manual
(2 pages)
(2 pages)
Sewing machines Ridgid 300 User Manual
(1 pages)
(1 pages)
Sewing machines Ridgid 1233 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 0.565 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals