RIDGID 1822-I Operator's Manual Page 10
- Page / 57
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Ridge Tool Company8
916 Roll Groover
Operating the 916 Roll Groover
WARNING
Do not wear gloves or loose clothing when oper-
ating a Roll Groover. Keep sleeves and jackets but-
toned. Do not reach across the machine or pipe.
Do not use this Roll Groover with a Power Drive or
Threading Machine that has a broken or missing
foot switch. Always wear eye protection to protect
eyes from dirt and other foreign objects.
Keep hands away from grooving rolls. Do not wear
loose fitting gloves when operating groover. Use
pipe stands to support pipe.
When grooving, keep hands away from end of
pipe. Do not reach inside pipe end.
Pipe Preparation
1. Pipe ends must be cut square. Do not use cutting
torch.
2. Pipe out-of-roundness must not exceed the total
O.D. tolerance listed in groove specifications, Table I.
NOTE! Determine out-of-roundness by measuring max-
imum and minimum O.D. at 90 degrees apart.
3. All internal or external weld beads, flash or seams
must be ground flush at least 2″ back from pipe end.
NOTE! Do not cut flats on gasket seat area.
Pipe/Tubing Length
Chart A lists the minimum length of pipe or tubing to be
grooved and the maximum length to be grooved with
(1) pipe stand.
Grooving pipe below 8″ in length increas-
es the risk of fingers being crushed in the grooving rolls.
Pipe Set-Up
1. Pipe or tubing longer than the specified maximum
lengths listed in
Chart A
must be supported with 2
pipe stands. The second pipe support should be
located
3
/
4
of pipe length from roll groover.
Failure to use two stands may result in
unit tipping or the pipe falling.
2. Lift up on feed handle and place pipe on drive roll and
pipe support.
3. Square pipe and pipe support to roll groover making
sure pipe is flush against drive roll flange.
(Figure 6)
4. Level pipe by adjusting pipe stand (Model 300PD,
535)
(Figure 7).
See tip for 1822 and 300 Compact
grooving on
page 10.
5. Slightly offset (approximately
1
/
2
°) pipe and pipe stand
toward operator when the power source operates in
REVERSE mode
(Figure 8)
.
NOTE! If power source runs in FORWARD offset pipe
1
/
2
° away from operator.
(Figure 8)
Figure 6 – Square Pipe & Pipe Support
Figure 7 – Leveling Pipe
Groovable Pipe Lengths – Inches
Nom. Min. Max. Nom. Min. Max.
Size Length Length Size Length Length
1 8 36 4 8 36
1
1
/
4
8364
1
/
2
832
1
1
/
2
836 5 832
2 8 36 6 O.D. 10 30
2
1
/
2
8 36 6 10 28
3836
3
1
/
2
836
Chart A – Minimum/Maximum Pipe Length
WARNING
WARNING
- Portable Roll 1
- Table of Contents 2
- General Safety Information 4
- Specific Safety Information 5
- Roll Groover Assembly 6
- Instructions 6
- Description, Specifications 6
- Standard Equipment and 6
- (Figure 2) 7
- Machine Inspection 8
- Machine and Work Area Set-Up 9
- Pipe Preparation 10
- Pipe/Tubing Length 10
- Pipe Set-Up 10
- Adjusting Roll Groove Depth 11
- Forming the Roll Groove 12
- Pipe Diameter Reference 12
- Removing and Installing 13
- Roll Grooving Smaller 14
- Diameter Steel Pipe 14
- Accessories 14
- Roll Grooving Copper with 14
- Maintenance Instructions 15
- Service and Repair 15
- 916 Roll Groover 16
- Ridge Tool Company14 16
- Table III. Troubleshooting 17
- Ridge Tool Company16 18
- Rainureuse à galets n° 916 19
- Table des matières 20
- Déconseillé 21
- Consignes de sécurité 22
- Description, spécifications 23
- Assemblage de la rainureuse 24
- (Figure 4) 25
- Inspection de la machine 26
- MISE EN GARDE 27
- AVERTISSEMENT 27
- Préparation des tuyaux 28
- Longueur des tuyaux 28
- Installation des tuyaux 28
- (Figure 9) 29
- (Figure 10) 29
- Tableau B (Figure 11) 29
- Exécution des rainures 30
- Dépose et installation 31
- Exécution du rainurage 32
- Rainurage des tuyaux d’acier 33
- Accessoires 33
- Entretien 33
- Service après-vente 33
- Ridge Tool Company32 34
- Tableau III. Dépannage 35
- PROBLEME CAUSE REMEDE 36
- Tableau de dépannage 36
- Ranuradora a rodillos 37
- NO SE RECOMIENDA 39
- Información específica 40
- Descripción 41
- Especificaciones 41
- No. en el Modelo Peso 42
- (Figura 4) 43
- Revisión de la máquina 44
- ADVERTENCIA 45
- Funcionamiento de la 46
- Ranuradora a Rodillos No. 916 46
- Regulación de la profundidad 47
- (Figura 10) 48
- (Figura 11) 48
- Ranurado de tubos cortos 49
- Extracción e instalación 50
- Ranurado en cobre con la 51
- Ranurado de tubos de acero de 51
- Accesorios 51
- Instrucciones para 52
- Mantenimiento y reparaciones 52
- Ridge Tool Company 51 53
- PROBLEMA CAUSA CORRECCION 54
- PROBLEMA CAUSA CORRECTION 55
- Tabla de detección de averías 55
- Ridge Tool Company54 56
- Ridge Tool Company 57
- 400 Clark Street 57
- Elyria, Ohio 44035-6001 57
Related products and manuals for Sewing machines RIDGID 1822-I
(55 pages)
Sewing machines Ridgid 1210 User Manual
(2 pages)
(2 pages)
Sewing machines Ridgid 300 User Manual
(1 pages)
(1 pages)
Sewing machines Ridgid 1233 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals