RIDGID 1822-I Operator's Manual Page 21
- Page / 79
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Ridge Tool Company
19
Pipe Support Stands
No. 819 Nipple Chuck (Right Hand Only)
No. 839 Adapter Kit
Pipe Adapters..............
1
/
8
″ through 1
1
/
2
″
Stud Adapters..............
1
/
4
″ through 2″ UNC
1
/
4
″ through 1
1
/
2
″ UNF
Accessories For Threading
By Close-Coupled Method
No. 241 Carriage Mount Kit
No. 141 Geared Threader….for threading
2
1
/
2
″ - 4″ pipe
Pipe Support Stand
NOTE! See Ridge Tool catalog for complete list of pipe
supports, thread cutting oil and dies.
Maintenance Instructions
WARNING
Make sure machine is unplugged from power
source before performing maintenance or mak-
ing any adjustment.
Oil System Maintenance
Periodic cleaning of oil reservoir and filter screens will
promote proper operation of machine. Replace cutting oil
when it becomes dirty or contaminated.
1. Remove and clean top chip pan screen.
2. Remove and clean secondary screen from chip pan.
3. Remove drain plug and drain cutting oil.
4. Clean oil filter screen and remove sludge built up in oil
reservoir.
DO NOT operate machine with oil filter in
bottom of oil reservoir removed. This could cause chips to
clog oil line and/or damage the oil pump.
NOTE! RIDGID Thread Cutting Oil produces high qual-
ity threads and maximizes die life. For informa-
tion concerning its use and handling, refer to the
labels on the oil containers. Disposal of the oil
should be in accordance with government reg-
ulations.
Spindle Bearing Lubrication
(Figure 22)
Figure 22 – Spindle Bearing Lubrication
Main spindle bearing lubrication ports are located on top
and at each end of the spindle housing.
Bearings are oil impregnated when manufactured and
will serve to lubricate spindle until scheduled mainte-
nance is performed.
Lubrication with 10 drops of SAE 20 Weight Nondetergent
oil is recommended every six months (more often under
heavy machine usage).
Front Jaw Insert and Centering Finger
Replacement
1. Run machine in the OPEN position to open jaws.
2. With machine OFF and unplugged, remove front
cover.
3. Loosen screw that holds jaw insert and centering
finger in place. This should allow jaw insert to separate
from jaw assembly. (Figures 23A & B)
4. On a workbench, drive out top pins holding centering
finger in place and install new centering finger.
NOTE! When driving pin out on workbench, do not bend
centering finger.
1822-I Pipe and Bolt Threading Machine
Model
No. Description
819 Nipple Chuck 1/2″ - 2″ NPT
819 Nipple Chuck 1/2″ - 2″ BSPT
839 Adapter Kit for No. 819 Nipple Chuck
821 Blade Type Cutter
822 Adapter Kit for No. 821 Blade Cutter
141 4″ Geared Threader NPT
141 4″ Geared Threader BSPT
241 Carriage-Mount Kit for No. 141 Threader
1460 Oil Pan Cover Kit
E-863 L.H./R.H. Reamer Cone
364 Wheel Type Cutter
Conversion Kit for Plastic Coated Pipe
Grooving Tool
E-1050 Saran Tool for 821
D471 45° Bevel, Cut-Off Tool for 821
344 Reamer
Gear Grease (1224 & 1822)
CAUTION
Spindle Housing
Bearing Lubrication
Ports
- Pipe and Bolt 1
- Threading Machine 1
- Table of Contents 2
- Pipe and Bolt Threading 3
- General Safety Information 4
- Specific Safety Information 5
- Standard Equipment 6
- Machine Assembly 7
- Figure 3 – Stand Assembly 8
- Figure 2 – Machine Dimensions 8
- Machine Inspection 10
- Machine and Work Area Set-Up 11
- Operation Using 12
- Machine-Mounted Tools 12
- Die Head 13
- Checking Thread Length 15
- No. 839 Adapter Kit 16
- No. 819 Nipple Chuck and 16
- Operation Instructions 17
- Using Geared Threaders 17
- Changing Dies 18
- Threading 2 18
- ″ to 4″ Pipe (45 RPM) 18
- No. 821 Blade Cutter and 19
- No. 822 Adapter Kit 19
- Left Hand Machine Operation 19
- Accessories 20
- Maintenance Instructions 21
- Spindle Conversion Kit for 22
- Plastic Coated Pipe 22
- Machine Storage 23
- Service and Repair 24
- 1822-IC 25
- Ridge Tool Company 26
- Machine à fileter 1822-I pour 27
- Table des matières 28
- Sécurité personnelle 29
- Sécurité du chantier 29
- Sécurité électrique 29
- Consignes de 30
- Description 31
- Spécifications 31
- Equipements de base : 31
- Accessoires 32
- Têtes de filières et filières 32
- Assemblage de la machine 33
- Inspection de la machine 35
- Préparation de la machine et 36
- Utilisation des outils 37
- Mandrin à raccords n° 819 et 42
- Utilisation des fileteuses 43
- Remplacement des filières 44
- Coupe-tubes à lame n° 821 et 45
- Inversion du sens de rotation 46
- (rotation à gauche) 46
- Entretien 47
- Lubrification de la machine 48
- Ensemble de conversion de 49
- Service après-vente 50
- Stockage de la machine 50
- Máquina Roscadora de tubos 53
- Modelo 1822-I 53
- NO SE RECOMIENDA 55
- Información específica 56
- Descripción, especificaciones 57
- Montaje de la máquina 58
- Figura 3 – Soporte 60
- Revisión de la máquina 62
- Preparación de la máquina y 63
- Empleo de herramientas 64
- Extracción del tubo 66
- Terrajas Modelos 816/817 68
- Mandril Niplero No. 819 y kit 69
- Instrucciones de 70
- Cambio de terrajas 71
- Engranajes No. 141 71
- Funcionamiento de la máquina 73
- Accesorios 74
- Mantenimiento del sistema 75
- Extracción del árbol 76
- Instalación del árbol 76
- Almacenamiento de la máquina 77
- Servicio y reparaciones 77
- 400 Clark Street 79
- Elyria, Ohio 44035-6001 79
Related products and manuals for Sewing machines RIDGID 1822-I
(59 pages)
Sewing machines Ridgid 1210 User Manual
(2 pages)
(2 pages)
Sewing machines Ridgid 300 User Manual
(1 pages)
(1 pages)
Sewing machines Ridgid 1233 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 1.526 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals