RIDGID 1822-I Operator's Manual download pdf (Page 10)

Ridge Tool Company

SeeSnake

microDrain™ Inspection System

Pre-Operation Inspection

WARNING

Before each use, inspect your microDrain System

camera and reel and correct any problems to re-

duce the risk of serious injury from electrical shock

or other causes and prevent machine damage.

1. Confirm that the power is off and if used with a cam-

era control unit (CCU) other than the MicroEXPLOR-

ER Camera monitor confirm that the CCU is not

connected to the unit. Inspect the system cable and

connectors for damage or modification.

2. Clean any dirt, oil or other contamination from the

microDrain System to aid in inspection and to prevent

the unit from slipping from your grip while transporting

or using.

3. Inspect the microDrain System for any broken, worn,

missing, misaligned or binding parts, or any other

condition which might prevent safe, normal operation.

Confirm that the unit is properly assembled. Make

sure that the drum turns freely. Inspect the pushrod

for any cuts, breaks, kinks or ruptures.

4. Inspect any other equipment being used per its in-

structions to make sure it is in good usable condition.

5. If any problems are found, do not use the unit until the

problems are corrected.

Work Area and Equipment

Set Up

WARNING

Set up the microDrain System and work area ac-

cording to these procedures to reduce the risk of in-

jury from electrical shock, fire, and other causes,

and to prevent damage to the microDrain System.

Always wear eye protection to protect your eyes

against dirt and other foreign objects.

1. Check work area for:

• Adequate lighting.

• Flammable liquids, vapors or dust that may ignite.

If present, do not work in area until sources have

been identified and corrected. The microDrain

System is not explosion proof. Electrical connec-

tions can cause sparks.

• Clear, level, stable dry place for machine and op-

erator. Do not use the machine while standing in wa-

ter. If needed, remove the water from the work

area.

• Clear path to electrical outlet, if used for monitor,

that does not contain any potential sources of dam-

age for the power cord.

2. Inspect the work to be done If possible, determine the

drain access point(s), size(s) and length(s), pres-

ence of drain cleaning chemicals or other chemicals,

etc. If chemicals are present, it is important to under-

stand the specific safety measures required to work

around those chemicals. Contact the chemical man-

ufacturer for required information.

If needed, remove fixture (water closet, sink, etc.) to

allow access.

3. Determine the correct equipment for the application.

The microDrain System is made for:

•1

" to 3" lines up to 30' long.

•

nspection equipment for other applications can

be found by consulting the Ridge Tool Catalog.

4. Make sure all equipment has been properly inspected.

5. Evaluate the work area and determine if any barriers

are needed to keep bystanders away. Bystanders

can distract the operator during use. If working near

traffic, erect cones or other barriers to alert drivers.

Setting Up The microDrain System

Connections

If using the microDrain Reel with a microEXPLORER

Camera monitor, no additional connections beyond those

described in the assembly section are needed when set-

ting up the unit for an inspection.

When using with SeeSnake camera control units (CCU’s),

unwrap the system cable from the cord wrap on the

microDrain Reel case. Attach the system cable connector

to the matching connector on the CCU. Align the guide pin

on the cable connector with the guide socket in the CCU

connector and push the cable connector straight in. A

ridge molded into the outside of the cable connector will

point up when the guides are properly aligned. Tighten the

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

RIDGID 1822-I Operator's Manual Page 10

Comments to this Manuals

Related products and manuals for Sewing machines RIDGID 1822-I