RIDGID metal detector User's Guide Page 88
- Page / 144
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operating Instructions
Learning the wand is the same as learning a product and can only be done when the Photeye
option in the Menus > Service > Configuration > System menu has been set to NO. Once
Ferrrite has been learnt then further access should be denied to prevent accidental use. To do
this, navigate to the Menus > Service > Options menu and set the Access Ferrite option to
NO.
Factory frequency setting for ferrite is selected from the smallest aperture dimension and will
be the same as the default frequency. Therefore, depending upon the band selected, it will be
from the same range listed above. Should there be a change to the set band then the ferrite
memory would have to be re-learnt using a frequency from the new band used.
Setting Up the Conveyor
To set up the conveyor, proceed as follows:
1.
Select Menus > Service > Configuration > System to display the System menu options
which are listed and described below.
2.
Use the Navigation Keys
to select each option in turn press the OK /
Enter Key
to enable the value to be edited.
3.
Use the Navigation Keys
to select the required option value and then
press the OK / Enter Key
to confirm the selection.
4. Repeat step 2 and 3 until you have selected and confirmed values for each option.
The System menu options available are as follows:
■
Photoeye
This option refers to the optional Product Registration Photo-eye that is located on the infeed
of the conveyor. When the option is enabled the photo-eye acts as a timing start point for both
correct detection and subsequent reject timing functions.
Select the YES option if a photo-eye is fitted and the NO option if it is not.
■
PEC fault
This option is displayed if the Photoeye option has been set to YES. When the option is
enabled, should the photo-eye become blocked for any reason a system fault will be
generated. Depending on the reject and conveyor setup the conveyor will then stop and/or a
reject actuation will occur. Three options are available for selection as follows:
O Off
Selecting this option disables the PEC fault functionality.
O
Latched
Select this option if the fault must be manually cleared after the PEC has been
unblocked.
o
Auto Clear (default)
Select this option if the fault is automatically cleared after the PEC has been unblocked.
■
PEC length
To ensure the correct operation of the detector and reject systems it is extremely important to
ensure that this setting is correct.
78
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Related products and manuals for Measuring, testing & control RIDGID metal detector
(5 pages)© 2020, manymanuals.com. All rights reserved. | 1.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals