RIDGID metal detector User's Guide Page 25
- Page / 144
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
About Metal Detection
Learn Feature
Purpose
The Learn feature incorporated into the metal detector completely automates the configuration of the
detector settings for a product. Three Learn process options are available.
Full Learn
The Full Learn process consists of following displayed instructions to pass a number of product
samples through the detector aperture.
The product samples used during any Learn process must be representative of the product to be run
and known to be free from metal contamination.
Normally at least eight product samples will be required. By using more than one sample the detector
can make adjustments if necessary for differences that may occur across the samples used.
A single product sample could be repeatedly passed through the detector but the resulting Learn may
not be as good and require an update when the product line is run
The best results will be obtained by passing the product samples in succession through the detector
in the time period dictated by the on-screen instructions. If possible you should Learn the product on a
running line so that the detector learns a product as it would normally be run.
See the Full Learn
section for further details.
Update Learn
The Update Learn process consists of following displayed instructions to pass a number of product
samples through the detector aperture. This process can only be used for products that have already
gone through a Full Learn process. See the Update Learn
section for further details.
Reverse Learn
The Reverse Learn process consists of following displayed instructions to pass a number of product
samples through the detector aperture. The detector in this mode is used to pass products that are
identified as containing a metal contaminant and reject products that do not.
For example, a product may contain a metal toy so the detector is used to pass products which
contain the toy and reject those that don't.
Learn Setup
You are able to make some manual adjustments to the Learn process settings, either before or after
carrying out a Learn process. See the Learn Setup and Learn Limits
sections for further details.
15
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Related products and manuals for Measuring, testing & control RIDGID metal detector
(5 pages)© 2020, manymanuals.com. All rights reserved. | 0.860 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals