RIDGID metal detector User's Guide Page 117
- Page / 144
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Logs and Reports
This chapter provides information about the available logs and reports that are generated from
information automatically collected by the IQ
3
Metal Detector.
To produce any report a Serial Link
must have been previously set up to match the device receiving
the report. Once a link has been established, any active report may be produced.
Reports
To set up the report options, proceed as follows:
1.
Select Menus > Set Up > Report Options to display the Report Options menu options
which are listed and described below.
2.
Use the Scroll buttons
to select each option in turn press the Tick button
to enable the value to be edited.
3.
Use the Scroll buttons
to select the required option value and then press
the Tick button
to confirm the selection.
4. Repeat step 2 and 3 until you have selected and confirmed values for each option.
The Report Options menu provides the following options:
■ Form Feed
When this option is enabled a page break is included between each report being printed.
Options of YES (enabled) and NO (disabled) are provided for selection.
■ Carriage Return
When this option is enabled, each report is started at the beginning of the next new line.
Options of YES (enabled) and NO (disabled) are provided for selection.
■ All Reports
When this option is enabled, all available reports are made available for selection and sending
to the connected device, instead of having to scroll down the list and select them individually.
The individual reports options will therefore not be displayed for selection. Options of YES
(enabled) and NO (disabled) are provided for selection.
■ Reports
Menu options are a available for selecting the following Reports. Options of YES (enabled)
and NO (disabled) are provided for selection.
o
Errors Report
o Faults Report
o Setup Report
o Contaminants Report
o Learn Report
o Status Report
o PV Test Report
107
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Related products and manuals for Measuring, testing & control RIDGID metal detector
(5 pages)© 2020, manymanuals.com. All rights reserved. | 1.302 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals