RIDGID CM1450 Operator's Manual download pdf (Page 11)

• Keep the cut-off piece free to move sideways after it is

cut off. Otherwise, it could get wedged against the cut-

off wheel and could be thrown violently.

• Clear everything except the workpiece and related

support devices off the table before turning the machine

on.

Use extra caution with large, very small or

awkward workpieces:

• Use extra supports (tables, sawhorses, blocks, etc.) for

any workpieces large enough to tip when not held

down to the tabletop.

• Never use another person as a substitute for a table

extension, or as additional support for a workpiece

that is longer or wider than the basic cut-off machine

table or to help feed, support or pull the workpiece.

• Do not use this tool to cut pieces too small to let you

easily hold the work with the vise.

• When cutting irregularly shaped workpieces, plan your

work so it will not slip, pinch the cut-off wheel and be

torn from the vise.

Cutting With Abrasive Cut-Off Machine

WARNING

Never cut wood, magnesium, masonry, stone or

ceramic with this tool.

Keep your face and body to one side of the abra-

sive wheel, out of line with possible thrown sparks

or dust.

Do not use any type of cutting lubricant with this

cut-off tool.

1. To start tool, firmly grasp the handle and depress the

trigger switch. Be sure to allow the motor to reach

maximum speed prior to cutting. This will help reduce

the risk of thrown workpieces.

2. When beginning a cut with the tool, care should be

exercised not to bump or slam the wheel into the

work. Once it has entered the workpiece, continue to

cut with an even smooth stroke. Do not apply exces-

sive pressure.

If the wheel is damaged do to misuse, it

may develop cracks and eventually shatter without warn-

ing.

NOTE! The faster a cut is made the less heat is creat-

ed in the workpiece, preventing discoloring,

and wheel life is prolonged. Cut with a steady

force without overloading the machine.

3. When the cut is complete, raise the wheel com-

pletely from the workpiece before releasing the trigger

switch and allowing the motor to stop.

If material becomes jammed, release the

trigger switch immediately and wait for all moving parts to

stop. Unplug cut-off machine before attempting to remove

the material.

Removing Workpiece

1. Turn the vice handle counterclockwise to release

the workpiece. Raise the quick release lever and

pull back on the handle to allow the workpiece to be

easily removed from the vise.

2. Slide the workpiece out of the machine keeping a firm

grip on the workpiece as it clears the machine.

To avoid injury from falling parts or equip-

ment tip-overs when handling long workpieces, make

sure that the end farthest from the unit is supported prior

to removal.

Tips For Using Abrasive Cut-Off

Machine

Life of the abrasive wheel will depend on proper use of the

cut-off machine. Procedures that should be followed are

as follows:

• Do not “jam” the abrasive wheel into the work or

apply excessive pressure while using this

machine.

• Let the machine reach full speed before starting to

cut.

• Only cut the type and size of material specified for

this machine.

• Do not grind against the side of the wheel.

• Clamp the material correctly and ensure that it is

center relative to the abrasive wheel.

Transporting The Cut-Off Machine

Before moving this tool, lock the power head in the lower

position using the chain (Figure 1). Check to ensure the

machine is unplugged from the power source.

Lift the machine by using the hand-hold areas in each side

of bottom of the base or by the carrying handle (Figure 1).

Use proper lifting technique. Bend your knees so you

can lift with your legs, not your back. Hold the tool close to

your body when lifting.

Never carry tool by the power cord or the trigger grip of

the plastic handle. Carrying the tool by the power cord

could result in damage to the cord resulting in electrical

shock or fire.

CM1450 14″ Abrasive Cut-Off Machine

Ridge Tool Company 9

WARNING

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 42 43

Comments to this Manuals

No comments

RIDGID CM1450 Operator's Manual Page 11

Comments to this Manuals

Related products and manuals for Power tools RIDGID CM1450