RIDGID ZRR84082 Use and Care Manual download pdf (Page 11)

11 - English

OPERATION

STORING A PRESET IN MEMORY

See Figure 9, page 17.

The memory feature saves frequencies as presets in the

radio’s memory. You can save up to ten frequencies in FM

mode (five in FM and five in FM2) and five frequencies in

AM modes.

To store a frequency in memory:

 Tune to the frequency you want to save.

 Press and hold any number until you hear a beep.

The memory location will appear on the display under

PRESET.

NOTE: Choosing a memory location where a frequency is

already saved will change the preset to the new frequency.

To recall a preset frequency:

 Press the numbered button corresponding to the memory

location number of the saved frequency.

 To exit a preset channel and return to Manual Tuning,

press one of the arrow keys.

STEREO/MONO (FM MODE ONLY)

See Figure 10, page 17.

To switch between stereo and mono broadcast:

 Press the MODE button until the Tools ( ) menu is

highlighted, then press Enter ( ).

 Press either arrow button until the Stereo menu is

highlighted, then press Enter ( ).

 Press either arrow button to switch between Stereo and

Mono and press Enter ( ) to store your selection.

STEREO will be displayed on the LCD screen when the radio

is in stereo mode and the selected FM station is broadcasting

in FM stereo.

TONE CONTROL

See Figure 10, page 17.

To adjust the bass and/or treble settings:

 Press the MODE button until the Tools ( ) menu is

highlighted, then press Enter ( ).

 Press either arrow button until the desired tone (Bass or

Treble) is highlighted, then press Enter ( ).

 Press the arrow buttons as desired to add or subtract

bass or treble, then press Enter ( ) to store your

selection.

SETTING THE CLOCK

See Figure 11, page 18.

The time appears on the LCD display when the radio is on. If

the time is flashing on the display, the clock needs to be set.

To set the clock:

 Press the MODE button until the Tools ( ) menu is

highlighted, then press Enter ( ).

 Press either arrow button until the Clock ( ) menu is

highlighted, then press Enter ( ).

 Use the arrow buttons to choose between the 12-hour

and 24-hour clock, then press Enter ( ) to store your

selection.

 Use the arrow buttons to set the correct hour, then press

Enter ( ).

NOTE: Pressing and holding the arrow buttons will cause

the numbers to advance more quickly.

 Use the arrow buttons to set the correct minutes, then

press Enter ( ) to store your selection.

USING THE REMOTE CONTROL

See Figure 12, page 18.

In most instances, the buttons on the remote control operate

the same as the buttons on the radio itself.

 The POWER button ( ) allows you to turn the radio on

and off.

 The MODE button displays available modes, allowing

you to choose between them using the arrow keys on

the remote.

NOTE: The Tools ( ) menu is unavailable from the

remote control. To activate anything within the Tools

menu, you must use the MODE button on the radio.

 Use the volume button ( ) to raise and lower the

volume of the radio.

 Press the arrow buttons to cycle between available

modes. When using an iPod, this button will also allow

you to move to the previous or next song in the playlist.

 The MUTE button mutes the audio.

 In iPod mode, the PLAY ( ) button starts and pauses

the iPod audio.

USING AN iPod/MP3 PLAYER OR CD PLAYER

(NOT INCLUDED) WITH THE JOB-SITE RADIO

See Figures 13 - 15, page 18.

For dockable iPod models (with 30-pin connector):

Made for iPod touch (2nd generation), iPod classic, iPod with

video, and iPod nano (2nd, 3rd, 4th, and 5th generation).

 Press the MODE button until the iPod menu is highlighted,

then press Enter ( ).

 Open the drop-down compartment door by pulling up on

the latch handle.

 Press the tabs on the front of the iPod cradle to lower the

cradle.

 Remove the cap from the 30-pin connector and place in

the storage area located at the back of the cradle.

 Insert the iPod (facing out) into the cradle. Make sure the

30-pin connector on the iPod is aligned with the 30-pin

connector in the cradle and that the iPod is pushed down

completely to ensure proper docking. The iPod should

begin to play automatically.

NOTE: Before inserting the iPod, choose the playlist (or

other group of items such as Album, Song, or Genre) on

the iPod you wish to listen to.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 43 44

Comments to this Manuals

No comments

RIDGID ZRR84082 Use and Care Manual Page 11

Comments to this Manuals