RIDGID ZRR86008K Use and Care Manual download pdf (Page 5)

5 - English

OPERATION

WARNING:

Do not allow familiarity with products to make you

careless. Remember that a careless fraction of a

second is sufficient to inflict severe injury.

WARNING:

Always remove battery pack from the tool when

you are assembling parts, making adjustments,

cleaning, or when not in use. Removing battery

pack will prevent accidental starting that could

cause serious personal injury.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1. Failure to do

so could result in objects being thrown into your

eyes, resulting in possible serious injury.

APPLICATIONS

You may use this product for the purposes listed below:

Drilling and driving screws in all types of wood products

(lumber, plywood, paneling, composition board, and hard

board), ceramics, plastics, fiberglass, laminates, metals.

INSTALLING BELT CLIP

See Figure 1, page 8.

 Align hole in belt clip with hole in tool’s base.

 Install screw to secure belt clip in place.

WARNING:

Battery tools are always in operating condition.

Lock the switch when not in use or carrying at your

side, when installing or removing the battery pack,

and when installing or removing bits.

INSTALLING/REMOVING BATTERY PACK

See Figure 2, page 8.

 Lock the switch trigger.

 Insert the battery pack into the product as shown.

 Make sure the latches on each side of the battery pack

snap in place and that battery pack is secured in the

product before beginning operation.

 Depress the latches to remove the battery pack.

VARIABLE SPEED SWITCH TRIGGER

See Figure 3, page 8.

The variable speed switch trigger delivers higher speed with

increased trigger pressure and lower speed with decreased

trigger pressure.

To turn the drill ON, depress the switch trigger. To turn it

OFF, release the switch trigger and allow the chuck to come

to a complete stop.

NOTE: A whistling or ringing noise coming from the switch

during use is a normal part of the switch function.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 3, page 8.

Set the direction of rotation selector in the OFF (center lock)

position to lock the switch trigger and help prevent accidental

starting when not in use.

Position the direction of rotation selector to the left of the

switch trigger for forward drilling. Position the selector to the

right of the switch trigger to reverse the direction.

NOTE: The drill will not run unless the direction of rotation

selector is pushed fully to the left or right.

NOTICE:

To prevent gear damage, always allow the chuck

to come to a complete stop before changing the

direction of rotation.

LED GRIP LIGHT

See Figure 4, page 8.

The LED grip light, illuminates when either the switch trigger

or LED grip light switch is depressed and when there is a

charged battery in the tool. If the drill is not in use, the time-

out feature will cause the light to start fading and then shut off.

INSTALLING/REMOVING BITS

See Figures 5 - 6, page 8.

The arrows on the keyless chuck indicate which direction

to rotate the chuck body to tighten or release the drill bit.

Do not use a wrench to tighten or loosen the chuck jaws.

 To install bits, lock the switch trigger.

 Open or close the chuck jaws until the opening is slightly

larger than the bit size you intend to use.

 Raise the front of the drill slightly and insert the drill bit.

WARNING:

Make sure to insert the drill bit straight into the chuck

jaws. Do not insert the drill bit into the chuck jaws

at an angle then tighten. This could cause the drill

bit to be thrown from the drill, resulting in possible

serious personal injury or damage to the chuck.

 Grasp and hold the collar of the chuck with one hand.

With your other hand, rotate the chuck body to close and

tighten the chuck jaws.

WARNING:

Do not hold the chuck body with one hand and use

the power of the drill to tighten the chuck jaws on

the drill bit. The chuck body could slip in your hand,

or your hand could slip and come in contact with

the rotating drill bit. This could cause an accident

resulting in serious personal injury.

 To remove bits, lock the switch trigger and open the

chuck jaws.

 The bit provided with the drill can be placed in the storage

area, located on the base of the drill.

1 2 3 4 5 6 7 8 9 10 ... 19 20

Comments to this Manuals

No comments

RIDGID ZRR86008K Use and Care Manual Page 5

Comments to this Manuals

Related products and manuals for Power drills RIDGID ZRR86008K