RIDGID WL1200 Operator's Manual

1This Caster Set has been engineered and manufactured to our high standard for dependability, ease of operation and op-erator safety. When properly ca

10ASSEMBLYn Refer to the assembly diagram (located in the back of the manual) to determine the distance required between the legs for each type of

11ASSEMBLYStretch the spring to an approximate overall length of 13-15 inches, and attach the spring s-hook to the chain as shown. The spr

12ASSEMBLYMODEL TS2412, TS2424 TABLE SAWSee Figures 18-20.Parts Not Used:n Upper Assembly Hex Head Screw, 1/4-20 x 1-1/2 (2) Washers, 1/4 in. (2)

13ASSEMBLYMODEL BS1400 BAND SAWSee Figures 21-23.Parts Not Used:n Upper Assembly Hex Head Screw, 1/4-20 x 1 1/2 (2) Washers, 1/4 in. (2) Lock Nuts

14ASSEMBLYMODEL RS1000 RADIAL SAWSee Figures 24-26.Parts Not Used:n Assembly To Legs Spring (1) S-Hooks (3) Chain (1) Band Saw Leg Brackets (4)Fi

15ASSEMBLYMODEL TP1300LS THICKNESS PLANERSee Figures 27-29.Parts Not Used:n Upper Assembly Hex Head Screw, 1/4-20 x 1-1/2 (2) Washers, 1/4 in. (2)

16ASSEMBLYMODEL MS1250LS MITER SAWSee Figures 30-32.Parts Not used:n Upper Assembly Hex Head Screw, 1/4-20 x 1-1/2 (2) Washers, 1/4 in. (2) Lock N

17ASSEMBLYMODEL WL1200 WOOD LATHESee Figures 33-35.Parts Not Used:n Upper Assembly * Tubes, 11 in. (2)n Lower Assembly Hex Head Screw, 1/4-20 x 1-

18ASSEMBLYMODEL AC9910 UNIVERSAL LEGSETSee Figures 36-38.Parts Not Used:n Upper Assembly Hex Head Screws, 1/4-20 x 1-1/2 (2) Washers, 1/4 in. (2)

19ASSEMBLYThe table below is for the various settings of the Universal Legset model AC9910. Measure the approximate width and depth of your legstand a

2n Introduction ...

20n The caster set is activated by pressing down on the metal platform. This will raise the legstand and allow the unit to be moved to the d

21EXPLODED VIEW/REPAIR PARTSHerc-U-Lift Plus Caster Set Model AC9950RIDGID parts are at www.ridgidparts.comFigure 1- Upper Assembly1356721181094123467

22EXPLODED VIEW/REPAIR PARTSHerc-U-Lift Plus Caster Set Model AC9950RIDGID parts are at www.ridgidparts.comFigure 2- Lower Assembly1171191119467614128

23EXPLODED VIEW/REPAIR PARTSHerc-U-Lift Plus Caster Set Model AC9950RIDGID parts are at www.ridgidparts.comFigure 3- Plate Assembly1234567891011131210

24Customer Service Information:For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant informatio

3RULES FOR SAFE OPERATIONSafe operation of this accessory requires that you read and understand this operator's manual, the operator’s manual for

4SYMBOLSSAVE THESE INSTRUCTIONSUNPACKINGNOTE: Before beginning assembly, check that all parts are included. If you are missing any part, do not assemb

5TOOLS NEEDEDThe following tools (not included) are needed for properly assembling your Herc-u-Lift Plus.WRENCHES (4)(7/16 in., 1/2 in., 11/16 in.)LOO

6ASSEMBLYFig. 1n This caster set is designed to fit many different wood working products. The basic assembly is the same for all application

7ASSEMBLYn Position the rear support assembly (from step 4) under the 23 in. tubes (from step 3) again referring to the assembly diagram (

8ASSEMBLYn Place U-bolt through holes in the U-bolt support assembly from step 3. Assemble the (4) 5/16 in. nuts on each side of the U-bolt wi

9ASSEMBLYASSEMBLY TO LEGSSee Figures 8-10.The caster frame is adjustable to fit a variety of tools. This manual includes assembly diagra